Skip to content

Do Electric Injection Moulding Machines Need Hydraulic Oil?

7 min readElectric Injection Moulding Machines

Clean electric injection moulding machine with no hydraulic oil tank or hoses in a factory

No. All-electric injection moulding machines have no hydraulic system, so they need no hydraulic oil, pump, tank or oil hoses. They are not completely oil free, though. Their moving parts, such as ball screws and toggle pins, still need grease or a small amount of lubricating oil. Hybrid machines are different, because they still use hydraulics on the clamp side.

Key Takeaways

  • Electric machines use servo motors and ball screws instead of oil pressure.
  • They need no hydraulic oil, so there are no oil leaks, filters or oil disposal.
  • They still need grease or lubrication for moving parts.
  • Hybrid machines are not oil free, so check the type before you buy.

Introduction

When buyers first hear about electric injection moulding machines, they hear one line again and again: no hydraulic oil. It sounds simple, but it raises real questions. Is the machine truly oil free? What does it need instead? Does it need less care?

This blog answers these questions in plain words, so you know exactly what to expect before you spend money.

Table of Contents

  1. What “No Hydraulic Oil” Really Means
  2. What Electric Machines Still Need
  3. Does No Oil Mean No Maintenance
  4. Where an Oil Free Machine Helps Most
  5. Common Myths About Oil Free Machines
  6. Electric vs Hybrid: The Oil Difference
  7. What to Ask Before You Buy
  8. Simple Care Tips
  9. Safety and Compliance Note
  10. FAQs
  11. Conclusion

What “No Hydraulic Oil” Really Means?

A hydraulic machine moves its parts with pressurised oil. It needs an oil tank, a pump, valves, filters, hoses and a cooler. Every one of these can leak, wear out or need a refill. The oil also gets hot as it works, so the machine needs coolers and extra cooling water to keep it in a safe range. Over time, hot oil breaks down and must be changed, and old oil must be disposed of the right way.

An all-electric machine removes this whole system. Each movement, such as clamping, injection, plasticizing and ejection, is driven by its own servo motor. The motor turns a ball screw, which pushes the part forward. No oil pressure is involved. You can read how this works step by step on our page for electric injection moulding machines.

Because the motors run only when a movement is needed, they can also work at the same time. This helps shorten the cycle, as we explain in our blog on All Electric Injection Moulding Machine Benefits.

What Electric Machines Still Need?

Here is the part many people miss. Electric machines have no hydraulic oil, but they still have moving metal parts, and those parts need lubrication.

  • Grease: Ball screws, toggle pins and guide bars are usually lubricated with grease. Many machines do this automatically.
  • Lubricating oil in some models: Some larger machines use a small closed oil system for the injection ball screw, because grease can harden or spread unevenly. This is a lubrication loop, not a hydraulic system.
  • Cooling: The mould, the feed throat and the drives still need cooling, though some makers report much lower water use than hydraulic machines.
  • Clean, steady power: Servo drives are sensitive to voltage swings, so good power supply matters.
ItemHydraulic MachineAll-Electric Machine
Hydraulic oilYesNo
Oil pump, tank and hosesYesNo
Grease or lubrication for moving partsYesYes
Cooling needsHighLower
Risk of oil leakPresentNone from hydraulics

Does No Oil Mean No Maintenance?

No oil means less maintenance, not zero maintenance. You skip some of the most common hydraulic jobs, such as oil changes, filter changes and hose repairs. But other jobs stay.

PartWhat It NeedsWhy It Matters
Ball screwsRight grease at the right timeKeeps motion smooth and accurate
Toggle pins and guidesRegular lubricationPrevents wear and noise
Servo drivesClean cabinet and working fanHeat shortens drive life
Sensors and cablesVisual check and tightnessLoose cables cause false alarms

Always follow the maker's manual for grease type and timing. Using the wrong grease can harm a ball screw.

Greased ball screw and linear guide inside an electric injection moulding machine

Where an Oil Free Machine Helps Most

Being free of hydraulic oil is a big plus in some factories.

  • Medical and clean production: No hydraulic oil means no risk of oil dripping or misting near the mould. Our blog on Medical Plastic Injection Moulding Regulatory Sterilization Needs explains why cleanliness matters so much in this field.
  • Food packaging and caps: A clean floor and clean parts help with hygiene checks.
  • Electronics: Small precise parts need steady, clean moulding.
  • Plants that dislike oil handling: You save on oil purchase, storage and disposal.

An oil free machine also keeps the shop floor cleaner and safer, since there are fewer slippery spots from leaks. It also gives off less waste heat, which can ease the load on your factory cooling. For a plant in a hot city, this is a small but real saving each month.

Common Myths About Oil Free Machines

Myth 1: Oil free means no lubricant at all. Not true. Metal parts that slide or roll still need grease or a little oil.

Myth 2: Every servo machine is an electric machine. Not true. Many servo machines are servo-driven hydraulic machines, which still use hydraulic oil. The servo motor only runs the pump. Our blog on the Servo Motor Role in Injection Moulding Machine explains this difference clearly.

Myth 3: Oil free means you never clean up. Grease can still seep out if it is overfilled, so wipe and check now and then.

Think of the cost of hydraulic oil over the years. You buy it, top it up, filter it, change it and pay to dispose of it. A leaking hose can also stop a machine in the middle of an order. An electric machine removes this whole list of jobs, and that is why many plants see it as a long-term saving.

Electric vs Hybrid: The Oil Difference

This is where buyers get confused. A hybrid machine uses an electric motor for the screw, but still uses hydraulics for the clamp. So a hybrid is not oil free.

Machine TypeHydraulic Oil Needed?Where Oil Is Used
Standard hydraulicYesWhole machine
HybridYesClamp side
All-electricNoNot used

If you are still choosing between the two, read our blog on Electric vs Hybrid Injection Moulding Machines. If you want a heavy-duty hydraulic option instead, you can look at our Extruder Hydraulic Injection Moulding Machine.

An electric machine usually costs more at the start. The saving comes later, through less oil, lower power use and cleaner running. For a full buying checklist, see Choosing Electric Injection Moulding Machines. If you want to know whether an oil free machine suits your product, share your part details with our team on the Contact Us page.

What to Ask Before You Buy

Not every electric machine is built the same way, so ask the maker a few direct questions. Which parts are greased, and is it done automatically? Does the injection ball screw use grease or a small oil loop? How much cooling water does the machine need? What service and spare parts can you get in India, and how fast? Good answers here tell you a lot about how easy the machine will be to run for the next ten years.

Simple Care Tips

  • Use only the grease type the maker recommends.
  • Keep the area around the ball screws clean and free of dust.
  • Check that the drive cabinet fan and vents are clear.
  • Keep a log of lubrication dates, so nothing is missed.

Technician greasing the guide of an electric injection moulding machine

Safety and Compliance Note

Servo drives carry high voltage, even after the machine is switched off. Only trained people should open drive cabinets. Always lock out the machine before any repair or greasing work near moving parts. Machines should follow safety rules such as ISO 20430.

FAQs

Do electric injection moulding machines need hydraulic oil?

No. They use servo motors and ball screws, so there is no hydraulic oil, pump or tank.

Are electric injection moulding machines completely oil free?

Not fully. Moving parts like ball screws still need grease or a small amount of lubricating oil.

Is a hybrid machine oil free?

No. A hybrid uses hydraulics on the clamp side, so it still needs hydraulic oil.

Do electric machines need less maintenance?

Yes, because you skip oil changes, filter changes and hose repairs. Lubrication and drive care are still needed.

Are electric machines good for cleanroom moulding?

Yes, they are a good fit, because there is no hydraulic oil to leak or mist near the mould.

Conclusion

Electric injection moulding machines do not need hydraulic oil, and that is a real advantage for clean, low-leak production. They still need grease, cooling and clean power, so plan simple care routines from day one. Hybrid machines keep some hydraulics, so always ask which type you are buying. At KSB Machinery LLP, we explain these points clearly before you order, so you pick the machine that suits your product and your plant. Match the machine type to your needs, and the oil question will answer itself.

More from the blog

Electric injection molding machine manufacturers in India

Electric Injection Moulding Machines

Electric Injection Molding Machine Manufacturers in India

Electric injection molding machine manufacturers use servo motors instead of hydraulic pumps to run the clamping, injection, and ejection units. This cuts power use by 30-70%, gives cleaner precision, and…

5 min readRead More »